Temperature regulators
Accessories for water baths Optima™ series
Drain syphon SY1: For the rapid draining of baths.Heat exchange coil CW5: For use with precision and general purpose stirred baths. Temperature range 2 °C above coolant temperature. Coil diameter/l mm 77/55, pipe bore inlet/outlet 7mm.PP spheres PS20: Between operating temperatures 60 °C and 100 °C and below room temperature a lid or layers of polypropylene spheres can be used. Above 100 °C a lid must be used.
Air-to-water recirculating cooler AWC 100
The air-to-water recirculating cooler operates without a conventional refrigeration circuit and is a compact solution for dissipating small heat loads from external systems. A switch on the rear of the device can be used to adjust the fan speed for booster cooling (Stage 0: normal cooling capacity, virtually silent. Stage 1: higher cooling capacity, higher fan speed).Easy installation and operationVery quietLow maintenance
Bath fluid Algicide Aquastab
Protective agent for the prevention and control of algae formation in bath thermostatsRecommended dosage: 5 mL / 10 litres of water2 % poly(dimethylimino)-2-hydroxy-1,3-propanediyl chlorideUse biocidal products with care. Always read the label and product information before use.
Bath fluid Polyclear Mix 30 Plus
Prevents premature rusting and the growth of algae. Ideal for use in circulators, water baths, shaking water baths or heating baths. For routine applications from 5 to 90 °C.
Bath liquids for thermostatic baths
Bath liquids.Use of the appropriate liquids for heat transfer listed here offers many advantages:Safe to use, non toxic, and generally odourless formulationsResistance to ageing and viscosity changes with low susceptibility to corrosion.Silicone oils (SIL).Non-flammable, with long operational life.Synthetic heat transfer fluids (Synth).Usually formulated from a hydrocarbon base with low viscosity within the recommended working temperature range.Viscosity.For optimal temperature stability the bath fluid must be of low viscosity.Fire point.Fluids can spontaneously ignite above a certain temperature. EN 61010 stipulates that the maximum working temperature of the liquid should be 25 °C below its' fire point.Heating up range.Prolonged use is not permitted as the self-heating effect within these liquids may cause the overtemperature protection system of the pump unit to operate and shut down the pump.Operating temperature range.Thermostats may only be operated for an extended time in this range under certain conditions. Viscosity must not exceed 30 mPas. Otherwise pumps will not achieve their stated performance figures.Working temperature range.The long-term use range for peak thermostatic bath performance. Maximum viscosity level is approx. 5 mPas.
Bath tanks for Temperature control systems IC/ICC, plastic
Plastic tanks up to 100 °C, only for water.
Bath tanks for Temperature control systems IC/ICC, stainless steel
Stainless steel tanks up to 200 °C, with bath drain.
Beakers, glass, jacketed wiht PTFE-Olive, type T-GL
DURAN®. For heating and cooling liquids. Thermostatting liquid is circulating between the double walls of the beaker jacket. With glass-screw connections GL14 with PTFE olives (O.D. 9mm, T-GL2000 with GL18 and O.D. 11mm) for thermostat hoses. Coolant ram pressure: 0.5bar at maximum, operating temperature: +120°C at maximum. Special sizes available on request.
Beakers, glass, jacketed, type T
DURAN®. For heating and cooling liquids. Thermostatting liquid is circulating between the double walls of the beaker jacket. With glass olives (O.D. 12mm) for thermostat hoses. Coolant ram pressure: 0.5bar at maximum, operating temperature: +300°C at maximum. Special sizes available on request.
Beer Force-Ageing-Test Bath BFT®5
We offer special air cooled circulator for the Beer Force-Ageing-Test. It is equipped with a programmer for the change between 0 °C / 40 °C and 0 °C / 60 °C in a 24 hour cycle. Casings and bath parts are made of stainless steel.
Beer forcing test heating/cooling circulating bath
The forcing test heating/cooling circulating bath is used in conjunction with a photometer to determine the expected shelf life of beer before clouding. A temperature cycle simulates artificial ageing and is repeated until the first signs of cloudiness appear.Automatic temperature profiles simulate artificial ageingPreset temperature cycles for forcing testProgramme settings can be changed at any timeRemovable acrylic glass coverLarge bath opening with insert for 20 bottles of 0.5 lInfinitely adjustable, high-performance pressure pumpLarge colour TFT display, multilingual user interfaceIntegrated programmerIntegrated external Pt100 connectionRS232 interface for online communicationPID3 cascade temperature control for high temperature stability, both internally and externally
Booster heater for laboratory circulators MAGIO
The booster heater increases the heating capacity by 6 kW, thereby extending the range of applications for laboratory circulators. The booster heater consists of two components: a control unit and a heater unit with 2 x 3 kW. The heater unit is inserted into the bath opening in place of the bath lid. The control unit can be placed on top of or next to the circulator. The booster heater can be used in a temperature range of -50 to 300 °C. Permitted bath fluids: water, water-glycol, silicone oil.
Booster pump
The magnetically coupled centrifugal pump increases the pressure (up to 2.1 bar) or the flow rate in an application. It can be easily connected between various JULABO devices and the application. The stainless steel design of the pump provides excellent chemical resistance. Furthermore, the pump ensures leakage-free operation over a temperature range of -90 to 250 °C.
Bridge circulators MAGIO MS and MX
Thanks to the adjustable stainless steel bridge the thermostats can be used with bath tanks up to a filling volume of 100 litres and bath widths from 33 to 68 cm.Simple control of complex applicationsInfinitely adjustable, extremely powerful pressure and suction pumpLarge, high-resolution TFT touch display with multilingual user interfaceMedium-contacting parts made of stainless steelIntegrated programmerExternal Pt100 connectionUSB interfaceRS232 interfaceEthernet interfaceAnalogue interfaces (optionally)Classification III according to DIN 12876-1
Chiller DuraChill®, with positive displacement pump
Stable and reliable cooling for many common heat removal applications, including laser etching, AA furnaces, ICP, rotary evaporators, vacuum systems, reaction vessels, plasma etching, and condenser cooling.A bright, full-color touchscreen displayCooling at ambient temperatures up to 30 °CDynamicFilter™ self-cleaning filter systemLiquid level sensorUV light system to prevent growth inhibitorsUser-adjustable temperature, pressure, and flow rate alarmsExternal temperature tracking and communications capability (optionally)Cool Command™WhisperCool® noise reduction systemSelf-diagnostics service and functionality systemFront fill reservoir4 Casters, 2 of them locking
Chiller DuraChill®, with turbine pump
Stable and reliable cooling for many common heat removal applications, including laser etching, AA furnaces, ICP, rotary evaporators, vacuum systems, reaction vessels, plasma etching, and condenser cooling.A bright, full-color touchscreen displayCooling at ambient temperatures up to 30 °CDynamicFilter™ self-cleaning filter systemLiquid level sensorUV light system to prevent growth inhibitorsUser-adjustable temperature, pressure, and flow rate alarmsExternal temperature tracking and communications capability (optionally)Cool Command™WhisperCool® noise reduction systemSelf-diagnostics service and functionality systemFront fill reservoir4 Casters, 2 of them locking